• 323 Answers SOURCE: all machines thread the same. TTN tension,take up, needle. Beginning with the spool, guide the thread through the thread guides to the tension assembly. Pull the thread through the tension assembly and test it to make sure the tension is working correctly.

(To do this test,adjust your tension setting to normal or medium or 5 or something in the middle. Raise the presser foot and pull the thread through the tension. It should pull easily!! Lower the presser foot and pull the thread. It should pull noticeably harder.) If it passes this test, continue up through the take up lever,then down through the thread guides to the needle. Make sure your needle is fully inserted and turned the correct way.( If you load your bobbin case from the left side,the needle rule is normally FLAT to the RIGHT is RIGHT.

Sep 15, 2014 Threading diagram for Sears Kenmore 158.12270, 158 How to wind the bobbin on this machine: https://www.youtube.com.

Sears Kenmore 158.12270Kenmore Model 158.12270 Manual

There are some exceptions. If you have a newer style drop in bobbin or your bobbin case loads in the front then the rule is FLAT to the BACK. To wind the bobbin, guide the thread around the thread guide on the left top of your machine, then to the bobbin winder. Wind the thread around the bobbin several times, place the bobbin on top of the bobbin winder, push it against the wheel and press the foot pedal.

It should stop winding when the bobbin is full or you take your foot off the control Sewman7 Posted on Jun 05, 2008. • 1 Answer SOURCE: Not sure if I am too late, but it's pretty basic. I have the same machine. You have the thread on the spool with the thread on the left side (unrolling off the spool counterclockwise) and put it around the round thing on the front middle (looks like a snap sort of) and through the eye almost right in front of it (the loop) and hold the thread lightly then wrap the thread around the tensioner (the thing with the dial) to the left (counterclockwise) until the springs 'pops' it into place. Then run the thread through the little hook thing (by entering from the left) then up to the eye (hole) that is in the little arms that raises and lowers (you might need to spin the wheel to get the arm in the right position) then you run the thread back through the hook thing (entering from the left) around the little half circle thing (by entering from the left) and finally in the hole in the needle. Hope it made sense, I tried to use laymen terms.

Posted on Jul 09, 2008. • 69 Answers SOURCE: You put the hook (the half moon thing with a sharp point on it) in the machine by placing it opposite the little curved bar. Make sure it is seated properly on the ridge. The you take the race, the circular part with a small plate on the top and place that over the hook(the plate side will be facing up). Twincat 3.1 Keygen. It will only fit a certain way, it could have a slot that a notch fits into (that is usually how it goes).

Then slide the arms over it and they will snap into place. Once done, turn the handwheel and make sure everything moves smoothly. If not, you'll need to start over as something isn't seated correctly. U He Diva Keygen Mac Free. Then you can install the bobbin case as usual. Posted on Mar 01, 2009.

Kenmore 148 and 158 Models Instruction Manuals Kenmore Models 148 and 158 Instruction Manuals Please read all 'Terms and Conditions' on the Home Page before ordering Click to enlarge Kenmore Model 06 Instruction Manual / 1 / /. / Click to enlarge Kenmore Model 11 Instruction Manual / 2 / /. / Click to enlarge Kenmore Model 12 Instruction Manual / 3 / /.

/ Click to enlarge Kenmore Model 13 Instruction Manual / 4 / /. / Click to enlarge Kenmore Model 14 Instruction Manual / 5 / /. / Click to enlarge Kenmore Model 15 Instruction Manual / 6 / /. / Click to enlarge Kenmore Model 16 Instruction Manual / 7 / /. / Click to enlarge Kenmore Model 20 Instruction Manual / 8 / /. / Click to enlarge Kenmore Model 21 Instruction Manual / 9 / /.